35CrMo钢表面铁基激光熔覆层的组织和耐磨性能

采用CO2激光熔覆装置将LC3530铁基粉熔覆在35CrMo钢基体表面,研究了熔覆层的显微组织、硬度和耐磨性能,并与基体的进行对比。结果表明:基体组织为回火索氏体,晶粒尺寸在20μm左右,而熔覆层的组织为均匀细小的等轴晶,晶粒尺寸大多在8μm;基体的平均硬度为254.1HV,而熔覆层的平均硬度为640.5HV,且硬度分布更加均匀;在相同试验条件下,熔覆层试样的磨损量仅为基体试样的1/7,磨损系数是基体试样的1/5,且磨损后熔覆层试样的表面粗糙度较磨损前的大幅下降,表明激光熔覆后35CrMo钢的耐磨性能得到显著提高;基体试样的磨损机制为犁削磨损,而熔覆层试样的磨损机制为微观切削,其优异的耐磨性能与含有铁、铬、钼和碳等元素的高硬度合金碳化物的形成有关。     

Realization of 1 μm thick,crack-free and smooth PMN-PT film in the MPB through PLD: A comprehensive study

This paper presents a comprehensive study on the various hurdles and solutions in the realization of phase pure, pinhole-free and crack-free, 0.65PMN-0.35PT/LSCO/Pt/TiO₂/SiO₂/Si heterostructures using pulsed laser deposition. A few major inquiries were i) effect of excess PbO in the target, ii) modulation of deposition and annealing temperatures for the growth of LSCO buffer layer, iii) thickness of the buffer layer iv) effect of the flow of oxygen in the chamber during and after deposition and v) the annealing conditions; on the phase formation, morphology and leakage response demonstrated by the films. Ferroelectric response parameters viz. P_sat = 47.7 μC/cm², P_r = 20.03 μC/cm², E_C = 62.03 kV/cm and absolute area = 21460 units attest the quality of the grown film.     

Microstructure and oxidation behavior of NiCr-chromium carbides coating prepared by powder-fed laser cladding on titanium aluminide substrate

In the present study, a NiCr–Cr₃C₂ powder mixture was prepared by mechanical alloying and then coated on titanium aluminide substrates by the powder-fed laser cladding process using a set of optimum parameters. The high temperature oxidation behavior of the substrate and coating was studied by isothermal annealing at 900 °C for 5 h. It was found that the microstructure of the coating is composed of γ solid solution with different chromium carbide phases (Cr₃C₂, Cr₇C₃ and Cr₂₃C₆). The presence of different chromium carbides in the microstructure of coating can be attributed to the partial melting of primary Cr₃C₂ and the formation of non-equilibrium carbide phases during rapid cooling of laser cladding. The NiCr-chromium carbide laser cladded coating samples showed superior oxidation resistance compared to the substrate. The oxidation mechanism of both coating and substrate follow the parabolic law, where the parabolic rate constant of the coating was 20% of that of the substrate at 900 °C. Time-of-Flight Secondary Ion Mass Spectroscopy (ToF-SIMS) and Grazing Angle X-Ray Diffraction (GAXRD) analysis revealed that the surface of the oxide layer formed on the NiCr-chromium carbides coating and the substrate is mostly composed of Cr₂O₃ and TiO₂, respectively.     

Femtosecond laser micro-milling dental glass ceramics: An experimental analysis and COMSOL finite element simulation

Dental glass ceramic materials are widely used in all-ceramic restoration technology. In order to effectively solve the problems existing in the process of traditional diamond cutter milling dental glass ceramic materials, such as severe needle loss, large tool wear and general milling efficiency, a new method of ultrafast laser milling dental glass ceramics is proposed. In this paper, 1030 nm femtosecond laser with pulse width of 600fs was used to micro-mill dental glass ceramics. Confocal laser microscopy was used to measure the milling depth and surface roughness of single-layer milling under selected laser processing parameters. The pre-layered milling software was developed to control the z-axis lifting and to compensate the focal length synchronously. Scanning electron microscope (SEM), Raman spectrometer and Vickers micro-hardness tester were used to characterize the dental glass ceramics after femtosecond laser milling. The results showed that under the specific laser processing parameters, the infrared femtosecond laser milling system can achieve a good processing morphology without changing the surface composition and surface hardness of dental glass ceramics. This new dental glass ceramics processing method based on ultrafast laser technique indicated a new direction for further chair processing of dental all-ceramic restoration technology.     

Fabrication and laser performances of Yb:Sc2O3 transparent ceramics from different combination of vacuum sintering and hot isostatic pressing conditions

In this paper we report on the preparation and laser performance of transparent 3at.% Yb:Sc₂O₃ ceramics by reactive sintering of commercially available powders under vacuum followed by hot isostatic pressing (HIP). Combinations of different vacuum sintering temperatures (1650 °C and 1750 °C) and different HIP treatments (1700 °C and 1800 °C at 200 MPa) were tested in order to understand how these steps influence the microstructure and thus the optical and lasing properties of the ceramic samples. All the samples showed a good optical quality. The microstructure analysis and the laser tests showed that the vacuum pre-sintering temperature is the key factor determining the quality of the samples and the laser performances. The best values of slope efficiency i.e. η_L = 50 % and output power i.e. P_out = 6.62 W were obtained for the sample pre-sintered under vacuum at 1650 °C and hot isostatically pressed at 1800 °C.     

烟道流量计量标准装置

为了解决我国烟道流量计的量值溯源问题,中国计量科学研究院建立了烟道流量计量标准装置。装置使用可溯源至标准转盘的激光多普勒测速仪作为原级标准器,采用激光多普勒流速剖面扫描和超声流量计波动修正的方式测量标准流量,经校准的8声道超声流量计为工作级标准表,具备了908~104840m3/h的测量能力,扩展不确定度为0.62%(k=2),可对最大口径为1m的流量计进行校准。装置下游测试段包括圆形管段和矩形管段,能够开展烟道流量计测量性能的研究。     

半导体激光器辐照损伤效应实验研究进展

半导体激光器(LD)工作在空间辐射或核辐射环境中时,会受到辐照损伤的影响而导致器件性能退化。文章回顾了不同时期研制的LD(从早期的GaAs LD到量子阱LD和量子点LD)在辐照效应实验方面的研究进展,梳理了国际上开展不同辐射粒子或射线(质子、中子、电子、伽马射线)诱发LD辐射敏感参数退化的实验规律,分析总结了当前LD辐照效应实验方法研究中亟待解决的关键技术问题,为今后深入开展LD的辐照效应实验方法、退化规律、损伤机理及抗辐射加固技术研究提供理论指导和实验技术支持。     

基于随机光栅的可调谐随机光纤激光器

提出一种基于随机光栅与高反射布拉格光栅(FBG)相结合的可调谐随机光纤激光器。利用980nm泵浦光源泵浦一段7m长的掺铒光纤(EDF)进行增益放大,由随机光栅提供随机反馈。随机光栅长7cm,具有约10000个折射率修改点,这些点由飞秒激光逐点写入,并沿光纤方向随机分布,两点相邻间隔小于10μm。同时,利用中心波长为1548nm的高反射FBG来组成半开放腔结构,实现了随机激光的输出。实验测得的泵浦阈值功率仅为18mW,斜率效率高达13.2%,并通过改变FBG的中心波长,实现了输出激光波长的可调谐,调谐范围为4.45nm(1548.04~1552.49nm)。得益于半开放式激光腔的设计和EDF的高增益,整个系统具有阈值低、效率高、结构简单等优点。     

基于2D激光扫描的基准检测技术研究

在机器人自动制孔系统中,基准孔检测的准确性会直接影响整个机器人制孔过程的位置精度。为获取基准孔孔位准确信息,采用激光扫描的方式对基准孔进行检测。设计了2D线激光扫描在基准平面内点云的三维转化方法,通过分析基准孔在扫描仪坐标系下点云的分布特点,提出了一种基于坐标差值的基准孔边界提取算法。通过设定相邻点云在线激光扫描仪坐标系下z轴的坐标差值获取边界点,实验验证该算法能有效地去除点云中的噪声点,获取准确的基准孔边缘特征信息,进而得到准确的基准孔孔位信息。